Getting air out of brake lines without bleeding is a 15 to 20 minute task and you can do it yourself. You only need some basic tools and a helper as its a two person job. Process involve lifting vehicle, loosing bleeder nut, attaching tubing to brake line and bleeder, pressing the brake pedal to remove air and then just refilling the brake fluid.
You, me, and we all know that brake bleeding is a very difficult task. In most cases, this process takes a long hours. At the same time, there is no guarantee that the brake bleeding will be appropriate or not.
If your vehicle is left unattended for long periods, there is a high risk of air entering the brake system. It will feel spongy and soft when you apply the brakes. As a result, brake efficiency decreases.
So many like you find ways to get the air out of the brake system without bleeding. The good news is that in this article, we are going to give you a simple solution to that problem.
You can successfully remove air from the brake system without bleeding by using some simple tools and following the steps described in the article. So let’s start the process.
How Long Does It Take to Get Air Out of Brake Lines Without Bleeding?
The process we have given in this article is very simple and not difficult at all. You can hire an assistant to make the task easier. You will need to spend about 15-17 minutes on each wheel of your car.
Requirements You Will Need to Get Air Out of Brake Lines
Some very simple tools will be needed when you remove air from the brake line without bleeding.
- Rags
- Paper towels or cleaning cloth
- Plastic tube
- A container for catching old brake fluid
- A long plunger handle
- Brake fluid
- A helper
How to Get Air Out of Brake Lines Without Bleeding?
OK, this time we have reached our desired stage. You can easily get the air out of the brake line without bleeding by following the phases below:
Step 1: Jack Up the Vehicle
Lift the car with a jack. Then, remove the wheels and tires. Notice if there is any dirt or debris at the junction of the brake line. If any, wipe them off with a clean cloth. Make sure the place is completely clean. Now, let the place dry.
Step 2: Locate the Bleeder Bolt
To find the bleeder bolt, you need to look at the end of the brake caliper. There you will see a long cylindrical plug that’s a bleeder bolt. Its main function is to relieve pressure inside the brake line.
Step 3: Unscrew the Bleeder Bolt and Clamp the Tube
Loosen the bleeder bolt using a wrench. Then, place the tube over the open mouth of the brake line and attach it to the bleeder with the help of the wrench. Keep the tube long enough to facilitate work.
Step 4: Apply the Brakes
Now tell your assistant to push the brake pedal of the car a few times. When he/she presses the brake pedal, you will notice that some fluid coming out of the brake line each time the pedal being pressed.
Step 5: Rinse the Bleeder Bolt
At this stage, tell your assistant to stop pushing the brake pedal. Open the tube and clean the bleeder bolt thoroughly with a clean cloth.
You can also use compressed air instead of cloth. Apply some lube around the area connecting the line to the car so that there is no problem later.
Step 6: Replace or Add New Brake Fluid
Since all the air has been removed from the brake line, now you have to add new brake fluid. Remove the cap from the master cylinder reservoir.
Now add the brake fluid with the help of a funnel while holding the brake pedal. At this time there will be pressure in the reservoir. If there are any bubbles in the break line, then they will come out.
However, make sure that the fluid does not rise above the level. When the fluid is added, remove the parking brake and wait a few minutes.
Now the question may be how much fluid is needed. It depends on how much fluid you have flushed by pressing the paddle through the tubing. However, the amount should usually be about a quarter.
There may be a leak where the brake line is attached to the vehicle. To test it, pour a little fluid in that place and wait for a while to test it.
Step 7: Tighten and Preserve the Bleeders
Tighten the bleed bolt using a wrench and with the help of your assistant keep checking to see if there are any bubbles in the brake line.
When tightening, be careful that air from the brake line does not re-enter. Then, secure the brake line with a clutch-type clamp.
Step 8: Recite the Technique On Each Wheel
Apply the same process to the other wheels of the car in the same way that you have just got the air out of the brake line of one wheel.
However, be concerned about damaged or old brake lines as the brakes may fail at certain times after removing air from them.
This is even more dangerous on highways or busy roads. So you need to make sure that you can successfully remove all the bubbles.
Step 9: Refill the Brake Fluid Reservoir
Now check all the brake lines of your car again. Make sure there are no holes in the line for air to enter. Then, refill the reservoir with fluid.
Step 10: Do a Test Drive
Finally, you do a test drive. After driving, check to see if the cylinders are full of fluid. If you see any disturbance, such as air entering the line, repeat the above steps until you get the desired result.
How to Avoid Mess Up When Get Air Out of Brake Lines Without Bleeding?
When you go to remove air from the brake line, any kind of mistake can happen. Below are some pro tips to avoid them.
- Do not use grease or lube inside the break line with any sharp metal object. Use only authorized spray lube.
- Keep an account of each bleed. This will allow you to remember the total amount of fluid you have extracted or added.
- Seek the help of a skilled mechanic if possible.
- Take proper care of the car and maintain a safe drive.
Conclusion
Getting the air out of the brake line is a basic thing that every driver should know. Anyone can easily accomplish this with just a few steps. Only proper instructions and proper precautions must be followed.
We hope you enjoyed our article. We believe that with the combination of your basic automotive ideas and our above process you will be able to successfully remove air from the brake line without bleeding.
